New Equipment - Pretreatment
 
GAT

GAT Industrial Washers


Our polypropylene washer housing and heating system produces 25% to 40% reduction in energy use as compared to a steel washer housing design.

GAT commercial washers are the most dramatic advancement in pre-treatment washer design in years; And the energy savings is documented! But energy savings is only one of the many benefits. POLYPRO industrial washers also lower your overall maintenance costs. Polypropylene has a lower coefficient of heat transmission than steel or composite washer housings. GAT's exclusive use of it's high "U" exchanger offers the most efficient burner/exchanger process on the market. The firing rate of the burner components is reduced, thus adding life to your gas train and heat exchanger. Plus, polypropylene will not blister, swell or delaminate as hydroscopic composite materials are prone to do over time. The natural translucence of polypropylene allows ambient light to illuminate the interior of our industrial washer, providing a user friendly environment for both spray pattern observation and maintenance by your line personnel. There's no need for auxiliary lighting.

Standard Features Of Our Commercial Washers:
Stainless steel interior housing supports, conveyor shroud, screens, access doors, sump lids, and pump mounting plate Ten-year guarantee on washer housing against rust and corrosion Tanks, heat exchangers, drain boards and conveyor rails also available in stainless steel SCH 80 CPVC Quick disconnect risers and spray nozzles Vertically mounted pumps Highest heat transfer on the market Centrifugal vent fans for extended bearing life Manifold utility connections

Washer Applications:
Overhead-single or multi-line Belt washers Dip or spray/dip applications drum washers
GAT Washer

GAT Washers

 

ElectroSteam

Electro-Steam Generators


These steam units specifically designed for pre-cleaning and iron-phosphating metal surfaces prior to powder coating.

Benefits of pre-cleaning and iron-phosphating systems vs. other systems:

Clean, smooth, and receptive surface recommended for paint and powder coating processes. Prevents the spread of undercoat corrosion for surfaces that have been nicked or scratched.

Large spray booths are not required since there is very minimal overspray. Uses approximately 50% less chemical than a pressure washer system. Produces much less waste water than other systems. Savings generated as a result of fewer chemicals, less water, and less effluent.

Additional benefits include the following:
Standard Stainless Steel Cabinets
Built in accordance with ASME, UL, and CSA requirements
National Board of PVI Shop Inspected
98% efficient resulting in energy and water conservation
Low or high pressure dry steam in less than 15 minutes (or on demand)

A one year warranty on all parts and a five year warranty on the chamber.

Electro-Steam Generators

ElectroSyeam

 

Dinamec
Re-defining ‘clean’ for any industry

DINAMEC and SCHWING offers the solution for all your metal stripping needs. Our solutions safely remove all organic substances from all kinds of metal parts no matter the industry. From paint, powder coating, plastic, polyesters, and rubber, we can remove it. Our machines can be found in a wide variety of industries with over 2,000 installations worldwide. We ensure a clean and healthy stripping alternative to more traditional methods. Our technology offers many benefits from optimal results, no abrasive damage to tools or parts and a high operating capacity with low operating cost.

Dinamec

Decoring and Sand Reclamation, and Heat Treatment

Looking to remove the sand cores from your aluminum castings? This is often a tedious job due to the integrated design and hard organic binders. The Dinamec Systems’ Deco Fluid Bed Installation is the perfect solution for the gentle and smooth decoring of aluminum parts. Traditional methods take long periods of time, cause deformation or damage and have a high operating cost. Our systems offer quick cleaning time, no damage of parts and all at a lower operating cost. We are your decoring solution.



 






 

Powder Coating Equipment
Batch Systems
Turnkey Systems
Booths
Ovens
Pretreatment
Powder Application
Conveyors

Torrent Systems, LLC Electro-Steam Digilube Systems Rohner Nordson Corporation Wagner Systems, Inc Deimco Gema General Automatic Transfer - The Industrial Finishing Systems Leader
Rapid Industries Richards-Wilcox, Inc. DinamecSystems